Our products

Heat racing hydro prop. 2.7 dia. x 3.78" pitch. A good prop for 15cc glow & 26cc petrol

C.M.B. 67 Hydro Racing

A drum valve rear induction engine now avaiable with a new twin needle carburretor for better throtling at lower revs, than the venturi carb origanally fitted to both the 67 & 80 motors, which did not allow the engine to tick over at slow speeds. The 67 along with its big brother the 80RS feature the longer stroke engine, redesigned crankcase porting & new carb.



We still have spares available for the CMB 67 Evo & GP motors.
Crank rebuilds available on all engines.

CMB No. 7 Cold cone lock plug for medium to high nitro. 25% to 50%.

CONQUEST 43.5" in Carbon Fibre

The latest edition to the cat range of hulls from Aeromarine. This hull has been specially designed for the use of Zenoah type engines and high performance 15cc + glow engines.

The DU-BRO E/Z/ Adjust Ball Links are heavy duty with a adjustable ball joint clamp

A great prop for high performance .45 engines. 54.5mm (2.15") x 74mm (3.00") cupped to 3.3". would replace an Octura 1457"

A motor coupling for a 5/32"  smooth shaft to .098" flexi cable

Silicon Bronze prop.

Equivalent OCTURA prop  X447

Radio active 45mm Standard red nylon prop 4mm

Glass filled nylon prop 45mm

Using a "X" blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert

18" x 5mm stainless steel prop shaft & 8mm tube

  
High quality 18" x 1/4" stepped to  3/16" flexi . USA import.

SPEEDMASTER stainless steel trim plates with adjusting screws, plate is stainless with ali bracket. 2.00" wide x 2.00" long. Hieght of mounting plate is 5/8".

NEW SPDS-17SK Speedmaster small CNC strut blade with skeg. Ideal for 21.45 set ups on smaller hulls and fast electrics Needs to be fitted with 3/16" brass bushing bearing @ £6.75

Stub shaft OAL. 2.25" x 3/16" s/s stub shaft with 15mm of 4mm thread included in length. Drilled .150" (3.8mm)Octura flexi cable.
Longer length available

Stainless steel Stub shaft OAL. 2.25" x 3/16" with 15mm x 4mm thread included in length. Drilled to take .130" (3.2mm) cable. Longer length available

A stainless steel 3/16" x 3.25" with 15mm of 4mm thread and drilled to take .150" cable

Wire drive (.062") 1/16" to 2.5" x 4mm stub shaft
.
Shaft made to individual lengths. State when ordering.

WRBOLOX Octura extruded Ali long wedge wedge rudder blade with right hand WPU. Blade length 7.7/8" 8.7500"

Zenoah complete recoil pullstart and housing

Genuine Zenoah EZ pullstart. A much easier to use pullstart than the standard recoil drive dog one fitted to marine engines. Comes with all parts required to easily fit, Complete instructions sheet included.

BH_Hanson_Clutch This new clutch comes with a billet housing and a ventilated metal clutch bell. It's supplied with Zenoah clutch shoes, clutch housing, all mounting hardware and Aeromarine collett with your choice of round or square drive. The clutch is designed to be used with one of our clutch mounts or any mount using the Zenoah bolt pattern.

BH_Hanson_Clutch for G320 This new clutch comes with a billet housing and a ventilated metal clutch bell. It's supplied with Zenoah clutch shoes, clutch housing, all mounting hardware and Aeromarine collett with your choice of round or square drive. The clutch is designed to be used with one of our clutch mounts or any mount using the Zenoah bolt pattern.

Great 15cc rigger/hydro prop. 67mm diam. x 5.02" pitch for circuit and SAW. racing

 Good prop for 7.5cc surface drive mono & cats.

OCTURA 3/16" ID. x 5/16" OD. Plated hardened steel drive dog for use with the smaller range of Octura propellers with 5/16" hubs. Y536 and up to X442 and X6 series up to X645.

Octura Right hand lay 24" x 3/16" (4.76mm) cable

Octura Right hand lay 3/16" (4.76mm) cable

OCTURA coupling 1/8" to 1/16" (.062") wire drive