Our products

OCTURA 1/4"  ID. x 7/16" OD. Plated hardened steel drive dog. 2 grub screws.

OCTURA stub shaft 1/4" turned down to 3/16" with flats ground for securing connecting ferrule and 3/16" drive dog.

OCTURA 24" x 1/4" Right handed flexi cable

OCTURA Right handed 24" x 1/4" flexi cable squared at one end, only use for opposite rotation engines and props.

The Speedmaster single water pickup extended rudder puts the leading edge of the blade 4" behind the transom. (not Chineese copies)

Aeromarine aluminium servo tray for 1/4 scale servos measuring, 66.0 x 30.0 x 57.0mm. Easily mount your servos upright or lay down with these strong, aircraft aluminum trays. also available for standard size servos. SAVE £6.00 on NSP £10.95

ABC racing prop. 2.9 (75mm) dia. x 4.74" pitch ideal for 26cc petrol.

CMB 28.5cc petrol engine complete with exhaust system

TO ORDER ONLY

This pipe gives the engine faster acceleration and allows the engine to rev higher and produce more torque, also has a larger silencing section. One of the best 15cc pipes available.

CMB 45 piston pin clips

This is the famous and original outdrive unit from OCTURA. It is ideal for monos and cats and allows the strut to have greater adjustment that the use of a stinger drive. For use with engines from 6.5cc up to 35cc. The unit comes with an extuded allumium transom bracket for extra strength, a rudder with integral water pick up and the extruded profiled strut blade fitted with 1/4" lead teflon sleave bearings fitted in a reducer bushing and a nose piece to take a 11/32" brass prop tube.
A 55mm bar is supplied to enable the rudder to be offset to the side of the prop.

Silicon bronze surface drive prop for .61-.67 engines.

Comparable to Octura X452

The Speedmaster 4" extended rudder with tapered blade and single pickup, puts the leading edge of the blade 4" behind the transom.

Wedge rudder blade for the 60/90 rudder with a single water pick up

SPDUM-001-S Universal STD. Mount The Speedmaster enginge mount is fully adjustable for engines from 6.5cc up to 15cc. It comes with sets of different thickness spacers to enable all engines to fit between 4" or 5" stringers.

Aeromarine case hardened prop shaft. 4.25" x 1/4"  with 1/4unf thread.

Wire drive silver soldered  (.078") 2.5mm to 2.5" x 4mm stub shaft
Wire drive (.078")  2.5mm to 2.5" x 3/16" stub shaft.
Shaft made to individual lengths. State when ordering

Right handed rotation for use when contra rotating props are required and electrics with 36/40mm cans.

<strong>Octura</strong> 4.5"  x 1/4" stainless steel prop shaft only with flats milled for drive dog and ferrule grub screws.

Octura  S/steel 1/4" x 4.5" prop shaft complete with 7/16" OD. drive dog and brass prop nut. Shaft has flats milled to take drive dog and ferrule set screws.

OCTURA Tapered drive dog from 7/16" to 3/8" with 3/16" bore for all props with 3/8" dia. hub. Plated hardened steel.

OCTURA 36" x 1/4" flexi cable squared at both ends. Ideal if you only need 18" or less lengths as this can supply two.
"

OCFHE4MM13 Case hardened steel coupling for connecting a 4mm plain motor shaft to .130 (3.2mm) cable"

A2006 Aeromarine "T" brass water nipple with 1/8" bore.

45Rs 7.3mm conrod