Our products

OCTURA 3/16" id x 3/8" OD. Use with prop hub of 3/8" diam. ie. 45mm up to 65mm.

OCTURA 24" x 3/16" flexi cable squared at one end

OCFHE18098 Hardened plated steel electric motor collet coupling for connecting a 1/8" smooth motor shaft ie. 540 type motor to .098" flexi cable.

Radio box brubber ballows (2)

The easy way to install your standard size servo into the radio box. Servo lugs slide into the brackets once they have been secured onto the side or bottom of the box. For mounting all standard size servos. Very secure.

MADE TO ORDER ONLY 10 to 14 days. The Giant Apache. This large 56" Offshore deep V hull is suitable for the most powerfull of engines from 15cc up to 35cc, even a twin installation. Over the years it has had much racing success and is suitable for use in the roughest sea and lake conditions. UK delivery charge £28.00

Heat racing prop. 2.8 (72mm) x 4.48" pitch,Ideal for 15cc glow & 26cc petrol

AEROMARINE/Speedmaster  high quality 30" x 1/4" flexi shaft with a stepped down to 3/16" stainless steel stub shaft. USA import.

CMB 91 RS M-Line engine 

NEW
The latest 15cc engine from CMB 91RS.3 delivering loads of power. This engine has a new Crankcase, crankshaft, front housing, 4 bolt water jacket and a much revised Piston/liner set with 5 inlet ports an 3 exhaust ports.

CMB 45Rs ABC piston/liner set

Best choice for most .45 riggers with strong engines. 55mm (2.17) x 81mm (3.2") pitch (3.5" cupping

RC adjustable angle 1/4 Stinger drive . Very strong CNC machined aluminium drive unit with radio adjustment for shaft angle. Fitted with lead teflon bushes. To be used with 1/4"flexis, welded type

500ml (1/2 litre) IV petrol bag

Silicon bronze surface drive prop sutable for high power .45 engines.

Comparable to Octura X450

This unsilenced CMB 45 High Nitro pipe is ideal for fitting your own silencing system

 Brass sleeve for skeg strut and struts for soldered flange brass sleeve bushing SPDS-015

Replacement rudder blade with integral water pick up for the Mini rudder

Speedmaster Mini mono rudder. High quality CNC machined with water pick up.

Blade length 4

Transom to blade 2.25""

A high quality CNC wedge rudder with bearing block and single integral water pick upr. Suitable for use on 6.5cc to 13cc models, mono, cat or riggers.
Transom to leading edge of rudder 2.25"
Blade length 6"

Speedmaster single pick up tapered wedge rudder blade

Speedmaster 21 high quality CNC wedge rudder with integral water pick up. For 3.5cc to 7.5cc monos.



2.25 to leading edge of blade

Blade length 6" can be shortened"

 SPDS-008-200XB Large  2" extruded ali strut brackets

Genuine Speedmaster CNC alluminium strut blade with skeg and bracket..
Needs to be fitted with either 1/4" sleeve bearings or the brass bushing.
Made from high grade aircraft aluminum it comes complete with transom mounting "L" bracketS and fixing screws. The skeg helps to hold the hull in turns and is an added aid for protecting the propeller.
With brass sleeve and bushing fitted £43.90

The unit can also be modified with reducers and fitted with 3/16" lead teflon sleave bearings, £42.65.

 SPDS-13SK Speedmaster CNC Large skeg strut blade only.
brass sleeve has to be inserted for use of brass bushing
Needs fitting with either brass soldered end bushing at ££7.95 sleeve and bushhing
or 1/4" lead teflon sleeve bearings. (2 or 3) at .90p each

Can be bored for .130" (3.2mm)  or .150" (3.8mm) cable. Please state when ordering.

Longer or shorter lengths can also be supplied. State when ordering

Wire drive glued/silver soldered (.078")  2mm to 2.5" x 4mm stub shaft
Wire drive glued/silver soldered (.078")  2mm to 2.5" x 3/16" stub shaft  with 4mm thread.
Shaft made to individual lengths. State length when ordering.