Our products

Stainless steel surface drive prop for .67 engined monos and cats. Comparable to Octura X455

Dural Aluminum prop for .90 - .101 motors

Speedmaster Straight wedge rudder blade with twin water pickups.

Straight blade D/P Rudder Assembly with 4" bracket

Speedmaster Rudder straight wedge blade with twin water pick ups in the blade. Transom to leading edge of blade is 2.25"

Dual Pickup 60/90 Rudder Assembly with 1 5/8" Bracket and straight wedge rudder blade.  Suitable for riggers and cats

SPDR-013-1LB, 60/90 1" wide Rudder Assembly with 2 1/4" bracket & single pickup Dims. From transom to rudder leading edge 2 1/4"

Heavy duty male/female bobbin 1" x 3/4" as used in the BHHAnson mount and many of the American engine mounts with unc. threads.  A very strong bobbin ideal for petrol engine mounts. Complete with stainless steel nut, washers and bolt."

 A good prop for 6.5cc to 7.5cc low power motors and equivalent electrics and electrics with 40mm cans.

.098" Teflon tubing per foot length, for use with Octura .098" flexi cable only"

OCFHE5MM13S Short, Electric motor coupling for 5mm smooth shaft to .130" flexi cable.

Rubber bobbin 15mm x 15mm male/female with 4mm stud and cap bolt complete with stainless steel nut and washers

A 15" Flexi shaft using OCTURA .130 cable silver soldered into a 2.5" x 3/16" stub shaft which has 15mm x 4mm thread.

Please state if you require a longer stub shaft Uses Octura high quality cable

High quality 1/8" (3.2mm) bore thick walled non kink water/fuel tubing, per foot (300mm).

Octura cast stainless steel strut & skeg. Complete with nose piece reducer and either 1/4" or 3/16" LT sleave bearings. Please state which required when ordering"

Silicon bronze prop for 11 -13cc Monos and cats

Speedmaster 4 extention block only. Convert your short extended rudder to 4" from the transom"

X447,  pitch 2.90" 1.85" dia. x 2.59" pitch. Also available in right hand rotation. A great prop for the surface drive mono with 7.5cc motors" and electrics with 40mm cans.  i(e. 4092 motor} 

.130" (3.2mm) teflon tubing for use with Octura .130" flexi cable or 1/8". Fits 7/32" K&S brass tubing.
Sold per 12" (300mm) any length cut.

OCFHE5MM13L Hardened plated steel, Long motor collet coupling for 5mm smooth shaft to .130" (3.2mm) flexi cable.

A 15" long flexi shaft using .130" Octura cable to a 2.25" x 3/16" stainless steel stub shaft. The cable is silver soldered into the stub shaft.
We can also make the shafts to your own length and put a 4mm thread on the end if required. Please specify when ordering.

Uses Octura high quality cable Shafts made to any length.

Heavy duty Silicon water tubing, 4mm bore.. (2 metre length)

NEW  Rubber bellows fuel proof and with gromit type fitting. Only need to drill a 6mm hole and then push through the gromit fitting end. Seal with super glue or similar waterproof adhesive.

CMB 45RS Direct Drive Crankshaft now fitted with the larger 7.3mm crankpin for extra strength.

Small engine mount bobbins 15mm x 15mm with 5mm studs, complete with s/s nuts and washers.

A heavy duty cast Stainless steel strut blade with skeg which will help to protect your prop from serious damage. The strut comes fitted with a nose piece, reducer and either 3/16 or 1/4" lead teflon bearings.
Please specify 1/4" or 3/16" bearings when ordering

Stainless steel prop